How to fix a leaky faucet with a dripping bathroom faucet and replacement cartridge parts nearby
|

How to Fix a Leaky Faucet: Common Causes and Simple Repairs

DIY plumbing · leak diagnosis

The first step in learning how to fix a leaky faucet is finding where the water starts. A drip from the spout usually points to an internal valve seal, cartridge or washer; moisture at the handle, base or under the sink can have completely different causes.

Most simple faucet repairs use common hand tools, but replacement parts must match the faucet design. Shut off both supply valves and confirm the water is off before disassembly. If a shutoff valve leaks or won’t stop the flow, don’t open the faucet until the supply is safely isolated.

Before touching hardware

Tools and preparation for a faucet repair

Have a small adjustable wrench, appropriate screwdrivers and Allen keys, needle-nose pliers, a soft cloth to protect finishes, a container for clips and screws, and the exact replacement cartridge, washer or O-ring. Some repairs require a specialized cartridge puller. Only use manufacturer-approved plumber’s grease where recommended.

Photograph the faucet and check under-sink supply lines before starting. A leak at a hose or supply connection may have nothing to do with the cartridge inside the handle.

Diagnosis comes first

Find where the faucet is actually leaking

First wet locationPossible problemBest initial step
Spout drips when turned offCartridge, washer, valve seat or ceramic sealIdentify faucet type and replace compatible worn internal part.
Around handleO-ring, stem packing or cartridge sealInspect upper valve seals after water isolation.
Around baseGasket, spout O-ring, mounting or water tracking from aboveDry everything and locate the point where water first appears.
Under sinkSupply-line fitting, hose, drain connection or faucet bodyInspect connections separately; shut off water before handling.
Pull-down sprayerHose connection, sprayer seal or cracked lineCheck hose routing and manufacturer’s replacement components.
Before disassembly

Turn off both hot and cold under-sink valves, open the faucet to relieve pressure and cover the drain so small screws don’t disappear. Keep parts in order and photograph the assembly as you go.

Match the design

Which type of faucet do you have?

Cartridge or ceramic-disc

A handle moves a removable internal mechanism. A worn cartridge or seals can cause drips, stiff handles or leaks around the handle. Replacement must match model and orientation.

Compression or ball-type

Traditional compression stems seal with rubber washers against valve seats. Ball-style faucets can use springs, seats and multiple seals. Their repair steps differ from standard cartridges.

Identify the manufacturer and model whenever possible. Two cartridges that look alike can differ internally. Do not force a stuck cartridge or use pliers directly on a decorative finish.

How to fix a leaky faucet: labeled cartridge, O-rings, retaining nut, supply lines and aerator
Existing Builzee diagram of a cartridge-style faucet and its serviceable parts.
Most modern single-handle faucets

How to replace a leaky faucet cartridge

01 · Expose the handle screw

Find the small cap or hidden set screw, use the correct driver or Allen key and lift off the handle. Photograph parts as you remove them.

02 · Release the bonnet and retainer

Remove only the trim, clip, retaining nut or ring needed for access. Protect finishes and never overtighten or pry against brittle plastic.

03 · Remove and match the cartridge

Note orientation, then withdraw carefully. Mineral buildup can make it resist removal; use a manufacturer-approved puller if required. Match the manufacturer part number before purchasing.

04 · Inspect body and seals

Clean loose debris without scratching the valve seats. Replace worn O-rings or cartridge seals using approved replacement parts. Some seals permit a little silicone plumber’s grease; do not use petroleum lubricant on incompatible rubber.

05 · Reassemble and test slowly

Reinstall the cartridge in the original orientation, secure the retainer and handle, then reopen water gradually. Check for drips at the spout, handle and supply connections.

Traditional two-handle faucets

How to repair a compression faucet

Older two-handle compression faucets commonly use a rubber washer at the bottom of each valve stem. If the handle must be tightened harder and harder to stop a drip, the washer may be worn. Other faucet designs do not use this same arrangement.

Compression faucet repair diagram with valve stems, packing nuts, washers, valve seats and supply lines
Original Builzee illustration of two-handle compression-faucet repair components.
  1. Remove the handle: pop the cap and unscrew the handle after shutting off water.
  2. Remove the stem: loosen the packing nut or stem assembly with the appropriate wrench.
  3. Match the washer: replace with the correct diameter and thickness; also inspect O-rings and packing.
  4. Inspect the seat: a pitted or corroded valve seat may continue leaking with a fresh washer.
  5. Reassemble and test: tighten appropriately, restore supply slowly, and inspect both handles.
Leaks elsewhere

Handle, base, sprayer and under-sink leaks

Water at the handle

Look at cartridge O-rings, stem packing or upper seals, not just the main spout seal.

Water at the base

Check whether splashing or handle leakage is running down the faucet before assuming the base gasket has failed.

Swivel spout

Some fixtures have replaceable O-rings below the spout body; servicing these can differ from valve work.

Under the sink

Look for wet supply fittings, pull-down hoses and drain assemblies. Turn off the water first if tubing or connections need handling.

If the faucet body is cracked, its finish is failing, repeated cartridge replacements don’t solve the issue, or parts are discontinued, replacement may be more practical than repeated repairs.

Closeout

Faucet repair checklist

FAQs

Questions about faucet leaks

Why does my faucet drip even after changing the cartridge?

The replacement could be incorrect or misaligned, or the sealing surfaces or other components may be worn. Verify the exact faucet model.

Can I repair only an O-ring?

Some faucets have serviceable O-rings, while others integrate seals into the cartridge. Follow the manufacturer’s parts diagram.

Should I replace a very old faucet instead?

Replacement may be more economical if the body is damaged, repair parts are unavailable or multiple components are failing.

Can I remove the faucet without turning off the water?

No. Shut off and verify supply isolation before taking apart pressurized valve components.

Bottom line

Diagnose the leak, then replace the right seal

Most faucet leaks are easier to handle once the wet location and valve type are understood. Use exact replacement parts, protect the finish and test all joints after restoring water.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *